Hobby Adhesives Hobby Adhesive News Hobby Adhesive Tips and Tricks Hobby Adhesives Tips and Tricks
Accessories
Our CAs come in 1/2 oz., 1 oz. and 2 oz. sizes, along with an 8 oz. that has a no mess, easy pour bottle for economical refilling of our regular bottles. In addition to our line of extender tips and fine PTFE tubing that allow very small, controlled amounts of CA to be applied, we have CA applicators that come in both a regular and fine tip. Just squeeze the bulb and insert into an open CA bottle to draw out the amount you need. When using the PTFE tubing, cut one end at a 45 degree angle before inserting no more than 1/4 inch into the bottle top.
adhesive extender tip applicator - cyanoacrylate hobby glue - BSI - 301

#301 Extender Tip
For use over BSI's standard #312 top. Can be used with all thicknesses of CA except IC-Gel. The flexible tip can be cut to the length and/or inside diameter that is needed for a particular application.

adhesive extra fine extender tip applicator - cyanoacrylate hobby glue - BSI - 302 #302 Extra Fine Extender Tip
For use over the standard #312 top, it allows BSI's thin CAs (Insta-Cure, Insta-Flex and Super-Gold) to be applied a drop at a time. Thin CA tends to run everywhere, so these allow precise application.
adhesive extra long extender tip applicator - cyanoacrylate - BSI - 303 #303 Extra Long Extender Tip
For use over the standard #312 top, they provide a rigid tip with extended length to get thin and gap filling CA into hard to reach areas. They are very resistant to clogging and can be cleaned by soaking in acetone.
adhesive pocket extender tip applicator - cyanoacrylate hobby glue - BSI - 304 #304 Pocket CA Extender Tip
For use with BSI's Pocket CAs. It slips over the tip of the Pocket CA top to allow for finer application of the CA. With the tip, the CA can be applied to confined areas.
adhesive extender tubing - cyanoacrylate hobby glue - BSI - 305 #305 PTFE Tubing
Two foot length of tubing can be cut off to any length (usually 2"). With one end cut at a 45 angle, can be inserted 1/8" into Pocket CA top and into #312 top if it is cut down an additional 3/64". For thin CA.
adhesive applicator extra top - cyanoacrylate hobby glue - BSI - 312 #312 Extra CA Top
Replacement top that is on all of BSI's non-Pocket CAs. Tops can be soaked in acetone overnight to remove any buildup of CA on the inside and outside of the nozzle.
adhesive applicator extra cap - cyanoacrylate hobby glue - BSI - 313 #313 Extra CA Over Cap
Replacement colored cap that fits over the #312 top.
adhesive applicator extra top and cap - cyanoacrylate hobby glue - BSI - 314 #314 Pocket CA Top & Cap
Replacement combination of top and screw-on cap that has a built-in pin for Pocket CAs. Will fit on Pocket CA bottles only.
adhesive applicator long pipette - cyanoacrylate hobby glue - BSI - 321 - 322

#321 CA Applicator
Regular Tip Non-clog 6" long pipette for the application of gap filling and extra-thick CA. CA is sucked up into the applicator by inserting it into an open CA bottle with the bulb at the end compressed, like an eyedropper.

#322 CA Applicator
Fine Tip Non-clog 6" long pipette for the application of thin CAs. Can also be used for the fine application of Insta-Set accelerator and for applying fine lubricating oils. CA can be kept in the applicator for two weeks.  

cyanoacrylates - BSI odorless cyanoacrylates - bsi accelerators - bsi foam-cure - bsi threadlockers - bsi
adhesive accessories - bsi How to Use Cyanoacrylates - bsi Epoxies - bsi Adhesive Selection Chart - bsi
    site design: Studio 101 West Marketing & Design